xTool P3 CMYK Inkjet Module User Guide
Updated Nov 16,2026
Updated Nov 16,2026

Unboxing and First Use

Safety instructions

  • Recommended operating environment:
    • Operating temperature: 15 – 35°C (59°F – 95°F)
    • Operating humidity: 40 – 60% RH
  • Do not store the ink cartridge in environments with drastic temperature or humidity changes, or in high-temperature/high-humidity areas.
  • Keep the ink cartridge and the module out of reach of children.
  • Avoid direct sunlight exposure to the ink cartridge.
  • Do not touch the metal contacts or the ink nozzle on the cartridge.
  • Do not peel off the labels on the side of the ink cartridge.
  • Do not install or remove the ink cartridge while the device is powered on.
  • Ink is not edible.
  • If ink contacts the skin or eyes, rinse immediately with plenty of water. Seek medical attention if discomfort persists.

List of items

1 list of items.png

2 list of items.png

3 list of items.png

4 list of items.png

xTool P3 CMYK Inkjet Module

Ink catridge

Bottom cap

Module mounting plate

5 list of items.png

6 list of items.png

7 list of items.png

8 list of items.png

Placing board for inkjet test

Hex key

Screw

Moisturizing liquid

9 Grease.png

10 list of items.png

11 list of items.png

12 list of items.png

Grease

Inkjet test pad (with holder)

Inkjet test pad (spare)

Calibration card

13 list of items.png

14 list of items.png

15 list of items.png

16 list of items.png

Placing plate for flexible materials

Magnetic patch

Masking tape

User Manual

Assemble xTool P3 CMYK Inkjet Module

Install the ink cartridge

17 ink cartridge.png

(1) Take out the ink cartridge.

18 take out.png

(2) Peel off the protective film.

19 peel off.png

Note: DO NOT touch the metal contacts on the bottom of the ink cartridge.

20 do not touch.png

Install the ink cartridge

21.png

(1) Open the front cover.

22.png

(2) Slide the ink cartridge along the inner track of the inkjet module.

23.png

Note:

■ Install the ink cartridge in the correct direction. ■ Do not touch the ink nozzle.

(3) Push the ink cartridge gently away from you until it clicks into place and is fully seated.

24.png

Note: Ensure that the ink cartridge is facing the correct direction and that its contacts are properly seated against the inkjet module contacts.

25.png

(4) Close the front cover.

26.png

(5) Apply an appropriate amount of moisturizing liquid to the bottom cap sponge, then reinstall the cap securely.

Note: When adding the moisturizing liquid, moisten the sponge of the module cover without over-saturating it. Excess liquid may cause ink mixing in the nozzle, affecting print quality.

27.png

28.png

Install xTool P3 CMYK Inkjet Module

Note:

■ Use the inkjet module only with xTool P3. Before use, read and follow Safety Instructions and Quick Start Guide of xTool P3.

■ If any module is connected to the laser module in xTool P3, remove it before installing the inkjet module.

Remove the roller protective covers of the module mounting plate

29.png

30.png

Note: Please keep the roller protective covers properly. When not in use, please detach the inkjet module from the main unit and attach the protective covers to the rollers. Moreover, apply grease to the rollers regularly to prevent future lubrication issues.

31.png

Install the module mounting plate

(1) Press down the locking bars on both sides as illustrated.

32.png

33.png

(2) Snap the lower rollers under the belt.

34.png

(3) Snap the upper rollers above the belt.

35.png

(4) Ensure that the inkjet module is well installed. Then, release the locking bars on both sides.

36.png

(5) Connect the inkjet module with the pre-installed laser module.

37.png

38.png

Note:

■ When installing the inkjet module for the first time, press the knob and tighten it clockwise.

39.png

■ To remove the inkjet module, turn the knob on the inkjet module counterclockwise.

40.png

Install the inkjet module

(1) Pull out the cable from the reserved port. Then, align the fixing pins on the inkjet module with the holes in the module mounting plate to ensure proper seating.

41.png

(2) Unplug the dust plug from the laser module and insert the inkjet module's connector into the port.

42.png

(3) Insert the other end of the cable to the inkjet module port.

43.png

Note: After removing the inkjet module, you can plug the cable to the reserved port on the mounting plate.

44.png

Install the placing board for inkjet test

Note: Before installation, put a slat in place to better support the placing board.

46.png

45.png

47.png


Place the inkjet test pad

48.png

49.png

Place a material

Note:

■ For better printing results, ensure that the printing material has a flat surface. ■ This section describes the procedure for placing and securing material on the slats for printing. If you've purchased a honeycomb panel, refer to its user manual to secure materials.

Place a hard material

(1) Take out two slats and install four material clamps.

50.png


51.png

(2) Install the slats back to the main unit.

52.png

(3) Place a material between the material clamps. Adjust the slat position to ensure that the material is well secured.

Note: When using the inkjet module, do not clamp the material with the material clamps, as this may scratch the ink nozzle.

53.png

Note:

■ Before processing a flexible material, place the slats closer together to better support the hard material or the placing plate for flexible materials.

54.png

■ You can also use masking tape instead of material clamps to secure the four corners of the hard material or the placing plate for flexible materials to the slats.

55.png

Place a flexible material

56.png

(1) Position the placing board between the material clamps as shown in the previous steps.

57.png

(2) Place a flexible material on the board and secure it at all four corners using magnetic patches.

58.png

Maintenance

■ Replace the inkjet test pad when it is dirty.

59.png

60.png

■ After the printing, ensure that the cover is installed back in place.

61.png

■ Regularly apply a few drops of the included moisturizing liquid, purified water, or distilled water to the sponge of the module cover to keep it slightly damp.

Note: When adding the moisturizing liquid, moisten the sponge of the module cover without over-saturating it. Excess liquid may cause ink mixing in the nozzle, affecting print quality.

62.png

■ Avoid exposing the ink nozzle to air for extended periods. If residual ink or dust is present on the nozzle surface, gently wipe it with a lint-free cloth.

63.png

64.png

Note: For more information about xTool P3 CMYK Inkjet Module, visit support.xtool.com/product/69.

Preview
Was this page helpful?
0 out of 0 found this helpful
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
Help Ticket
Use this help ticket to submit your issue. We will respond within 1 business day
Submit a Ticket
xTool Logo

Contact Us

🇺🇸+1 (833) 588-4887
Service Live Chat

Copyright © 2026 xTool All Rights Reserved.